Specifications: 

1) Input voltage: AC100-240V 50-60Hz

2) Output parameter: 

    a) Ni-MH battery charger: DC10-30V 500-2000mA, charging for 6-15pcs 

        sealed batteries with intellectualized MCU control

    b) Lea-acid battery charger: (12V battery)DC13.8V 2,000-4,000mA; 

        (24V battery)DC27.5V 1,000-2,000mA

    c) Li-ion battery: DC12.6V 2,000-4,000mA, 16.8V 2,000-3,000mA 

        21.0V 1,000-2,000mA, 25.2V 1,000-2,000mA

    d) Power supply adapter: 12V 1,000-4,000mA, 18V 1,000-3,000mA, 

        24V 1,000- 2,000mA, 30V 1,000-2,000mA

3) LED display: 

    a) 1 LED 1 color indicates power on 

    b) 1 LED dual color, red LED will light up to signal that charging is in 

        processing, green LED will light up to signal that charging is completion

4) Limited charging current:: 1,000-4,000mA

5) Steady precision: 3%

6) Loaded effect: 5%

7) Efficiency: ≥85%

8) Dimensions: 148 x 78 x 44mm

9) Weight: 410g

10) Constant charging current and charging voltage, short-circuit protection

11) Operating conditions:

     a) Temperature: -10 to 40°C 

     b) Relative humidity: ≤85%

     c) Atmosphere pressure: 86 to 106KPa

12) Storage and conveyance conditions:

     a) Temperature: -40 to 60°C 

     b) Relative humidity: ≤90%

13) Insulation resistor: under the normal atmosphere condition, insulation

     resistor of product no less than 10Mohm, the loop of product can stand

     50Hz 3750V, 1min dielectric strength and no rupture

Specifications:
1) To adopt advanced exactitude switch power supply, worldwide input 
    voltage: AC100-240V
2) Little heat, save energy source, pollution free
3) Separate wire and charger
4) Streamline structure, small bulk (68 x 110 x 30mm)
5) Smart and easy to carry
6) Apply to charge 4pcs rechargeable batteries at same time or 
    charging by individual, allowing to charging different category 
    and capability of batteries
7) Through testing the voltage of each battery with minus 
    voltage increment control mode ( Less than 10mV) and temperature 
    to judge batteries are full charged or not
8) With intellectualized MCU control to test batteries application 
    when they are placed in the socket
9) Max charging current: L2A±10%
10) Trickle current: 50mA±10%
11) Max voltage of battery: 1.8V
12) Highest temperature of battery: 55oC±3oC
13) Max charging time:
    a) Charge1pc battery: 90minutes; 1800mAh    
    b) Charge 2pcs batteries: 150 minutes; 1800mAh
    c) Charge 3pcs batteries: 225 minutes; 1800mAh
    d) Charge 4pcs batteries: 300 minutes; 1800mAh
14) It will be judged battery short-circuit and start protection if 
    the voltage below 0.1V at any time
15) Defective battery will be inspected in 20 seconds charging time. 
    If the voltage can't up to 0.8V or over 1.8V, it will be judged 
    non-chargeable battery and stop charging, then indicates 
    troubleshooting
16) Indicator:
    a) Green LED will light up which indicates power on
    b) Red LED will light up which indicates charging is in processing
    c) Flashing: 1Hz, green LED will light up which indicates charging 
        is completed
    d) Flashing: 1Hz, red LED will light up which indicates non-applicable 
        battery
    e) Flashing: 1Hz, green LED will light up which indicates temperature 
        ascend to 55 and start protection function
17) Applicable to digital cameras, toys, MP3, recorders
18) Dimensions: 106 x 65 x 32mm
19) Weight: 180g
20) Operating temperature: -10oC±40oC
21) Operating relative humidity: ≤85%
22) Operating atmosphere pressure: 86-106Kpa
23) Storage temperature:-40oC±60oC
24) Storage relative humidity: ≤90%
25) Insulation resistor: under the normal atmosphere condition, 
     insulation resistor of product no less than 10Mohm, the loop of 
     product can stand 50Hz, 3750V, 1min dielectric strength and no 
     rupture


Outer packing:
Clamshell 
60pcs/ carton 
Carton size: 50 x 50 x 60cm
G.W.: 12.5kg